User Tools

Site Tools


adept_swap_in_ms2000

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
adept_swap_in_ms2000 [2016/05/12 12:13]
vik
adept_swap_in_ms2000 [2016/10/04 15:13] (current)
Line 9: Line 9:
   * optionally a few small zip ties   * optionally a few small zip ties
  
-{{ :​documentation:​adept_swap1.png?​direct&​300 |}}+{{ adept_swap1.png?​direct&​300 |}}
  
 ===== Part 1 MS-2000 Controller Adept Piezo board removal ===== ===== Part 1 MS-2000 Controller Adept Piezo board removal =====
Line 18: Line 18:
 Second, using the Phillips screw driver, remove the three upper screws that attach the top of the lid, see picture 2. Then turn the controller over on a small box or a piece of foam to protect the joystick and remove the three lower screws, see picture 3. Save the screws for reassembly. See pictures 2-5 below. Second, using the Phillips screw driver, remove the three upper screws that attach the top of the lid, see picture 2. Then turn the controller over on a small box or a piece of foam to protect the joystick and remove the three lower screws, see picture 3. Save the screws for reassembly. See pictures 2-5 below.
  
-[{{ :​documentation:​adept_swap2.png?​direct&​300 |Click to Enlarge}}]+[{{ adept_swap2.png?​direct&​300 |Click to Enlarge}}]
  
 Third, set the lid to the side and remove the three ribbon wire headers and two SMB connectors to the smaller Adept Piezo daughter board that is on top of the mother board, see pictures 6. See pictures 6 through 11 below for examples of each header being removed. Note that the SMB connectors may or may not need to have a zip tie cut with the wire cutters. See picture 11. Third, set the lid to the side and remove the three ribbon wire headers and two SMB connectors to the smaller Adept Piezo daughter board that is on top of the mother board, see pictures 6. See pictures 6 through 11 below for examples of each header being removed. Note that the SMB connectors may or may not need to have a zip tie cut with the wire cutters. See picture 11.
  
-[{{ :​documentation:​adept_swap3.png?​direct&​300 |Click to Enlarge}}]+[{{ adept_swap3.png?​direct&​300 |Click to Enlarge}}]
  
-[{{ :​documentation:​adept_swap4.png?​direct&​300 |Click to Enlarge}}]+[{{ adept_swap4.png?​direct&​300 |Click to Enlarge}}]
  
 Fourth, remove the four screws holding the board and move the board to an ESD safe location. See the pictures 12 and 13 below. Some screws may be below ribbon wires or headers. Fourth, remove the four screws holding the board and move the board to an ESD safe location. See the pictures 12 and 13 below. Some screws may be below ribbon wires or headers.
  
-[{{ :​documentation:​adept_swap5.png?​direct&​300 |Picture 12}}]+[{{ adept_swap5.png?​direct&​300 |Picture 12}}]
  
-[{{ :​documentation:​adept_swap6.png?​direct&​300 |Picture 13}}]+[{{ adept_swap6.png?​direct&​300 |Picture 13}}]
  
 Fifth, Repeat the above process with the other controller and remove the other Adept Piezo board. The Adept boards can now be traded and placed back into the controllers. If you are swapping from a MS-2000 controller to a RM-2000 controller or are swapping from rack to rack you will have to read part 2. Remounting the Adept board and closing the case is the same procedure in the first four steps in reverse. The cut zip ties can be omitted if they are not available. The SMB cables are attached with the case labeled “PZ sensor” to the SMB header marked with the “S” or “Sensor” and the case labeled “PZ Ext. In” to the SMB header marked with the “E” or “Ext. In” Fifth, Repeat the above process with the other controller and remove the other Adept Piezo board. The Adept boards can now be traded and placed back into the controllers. If you are swapping from a MS-2000 controller to a RM-2000 controller or are swapping from rack to rack you will have to read part 2. Remounting the Adept board and closing the case is the same procedure in the first four steps in reverse. The cut zip ties can be omitted if they are not available. The SMB cables are attached with the case labeled “PZ sensor” to the SMB header marked with the “S” or “Sensor” and the case labeled “PZ Ext. In” to the SMB header marked with the “E” or “Ext. In”
  
-{{ :​documentation:​adept_swap7.png?​direct&​300 |}}+{{ adept_swap7.png?​direct&​300 |}}
  
 ===== Part 2 RM-2000 (Rack Mount) Controller Adept Piezo board removal ===== ===== Part 2 RM-2000 (Rack Mount) Controller Adept Piezo board removal =====
Line 40: Line 40:
 First, using the Phillips screw driver, remove the nine lid screws that attach the top of the rack controller, see picture 14 above. Three are on the left, three on the right and three in the middle, see pictures 15 through 17 First, using the Phillips screw driver, remove the nine lid screws that attach the top of the rack controller, see picture 14 above. Three are on the left, three on the right and three in the middle, see pictures 15 through 17
  
-[{{ :​documentation:​adept_swap8.png?​direct&​300 |Picture 15}}]+[{{ adept_swap8.png?​direct&​300 |Picture 15}}]
  
-[{{ :​documentation:​adept_swap9.png?​direct&​300 |Picture 16}}]+[{{ adept_swap9.png?​direct&​300 |Picture 16}}]
  
-[{{ :​documentation:​adept_swap10.png?​direct&​300 |Picture 17}}]+[{{ adept_swap10.png?​direct&​300 |Picture 17}}]
  
-[{{ :​documentation:​adept_swap11.png?​direct&​300 |Picture 18}}]+[{{ adept_swap11.png?​direct&​300 |Picture 18}}]
  
 Second, remove the lid and set aside, as seen in picture 18.  Second, remove the lid and set aside, as seen in picture 18. 
Line 56: Line 56:
 If that is the case do so with the flat head screw driver but be careful not to damage the board or the cables or yourself, see picture 19. If that is the case do so with the flat head screw driver but be careful not to damage the board or the cables or yourself, see picture 19.
  
-[{{ :​documentation:​adept_swap12.png?​direct&​300 |Picture 19}}]+[{{ adept_swap12.png?​direct&​300 |Picture 19}}]
  
 Third, remove the three Adept PZ board ribbon wire headers, and the linear encoder header, and the two SMB connectors from the Adept board, see pictures 20 through 25. Note that the SMB connectors may or may not need to have a zip tie cut with the wire cutters, see picture 26. Third, remove the three Adept PZ board ribbon wire headers, and the linear encoder header, and the two SMB connectors from the Adept board, see pictures 20 through 25. Note that the SMB connectors may or may not need to have a zip tie cut with the wire cutters, see picture 26.
  
-{{ :​documentation:​adept_swap13.png?​direct&​300 |Picture 20}}+{{ adept_swap13.png?​direct&​300 |Picture 20}}
  
-{{ :​documentation:​adept_swap14.png?​direct&​300 |Picture 21}}+{{ adept_swap14.png?​direct&​300 |Picture 21}}
  
-{{ :​documentation:​adept_swap15.png?​direct&​300 |Picture 22}}+{{ adept_swap15.png?​direct&​300 |Picture 22}}
  
-{{ :​documentation:​adept_swap16.png?​direct&​300 |Picture 23}}+{{ adept_swap16.png?​direct&​300 |Picture 23}}
  
-[{{ :​documentation:​adept_swap17.png?​direct&​300 |Click to enlarge}}]+[{{ adept_swap17.png?​direct&​300 |Click to enlarge}}]
  
 Fourth, unscrew the four screws holding the board and move the board to an ESD safe location see pictures 27 through 31 below. Fourth, unscrew the four screws holding the board and move the board to an ESD safe location see pictures 27 through 31 below.
  
  
-[{{ :​documentation:​adept_swap18.png?​direct&​300 |Click to enlarge}}]+[{{ adept_swap18.png?​direct&​300 |Click to enlarge}}]
  
-[{{ :​documentation:​adept_swap19.png?​direct&​300 |Picture 31}}]+[{{ adept_swap19.png?​direct&​300 |Picture 31}}]
  
 Fifth, Repeat the above process with the other Rack mount controller and remove the other Adept Piezo board. The Adept boards can now be traded and placed back into the controllers. If you are swapping from a RM-2000 controller to a MS-2000 controller you will have to read part 1, if you have not already, to know how to remove the Adept board from that controller. Remounting the Adept board and closing the case is the same procedure in the first four steps in reverse. The cut zip ties can be omitted if they are not available. The SMB cables are attached with the case labeled “PZ sensor” to the SMB header marked with the “S” or “Sensor” and the case labeled “PZ Ext. In” to the SMB header marked with the “E” or “Ext. In” Fifth, Repeat the above process with the other Rack mount controller and remove the other Adept Piezo board. The Adept boards can now be traded and placed back into the controllers. If you are swapping from a RM-2000 controller to a MS-2000 controller you will have to read part 1, if you have not already, to know how to remove the Adept board from that controller. Remounting the Adept board and closing the case is the same procedure in the first four steps in reverse. The cut zip ties can be omitted if they are not available. The SMB cables are attached with the case labeled “PZ sensor” to the SMB header marked with the “S” or “Sensor” and the case labeled “PZ Ext. In” to the SMB header marked with the “E” or “Ext. In”
adept_swap_in_ms2000.txt · Last modified: 2016/10/04 15:13 (external edit)