User Tools

Site Tools


assembly_instructions_for_ramm

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
assembly_instructions_for_ramm [2016/05/23 23:23]
vik
assembly_instructions_for_ramm [2019/04/18 23:33] (current)
Line 1: Line 1:
 +====== Assembly Instructions for the RAMM ======
 +
 +<WRAP center round info 60%>
 +Be sure to locate and remove all parts and tools from the packaging.
 +</​WRAP>​
 +
 +===== Part 1: Parts list =====
 +
 +Step 1: Remove all the parts from the packaging. They should include: __two Upright Arches, (A)__, with four __Foot Clamps, (B)__, attached by 8 cap screws, four __Cross Bars, (C)__, with 12 cap screws attached, one __Alt Cross Bar__ with __Cross Bar Mount__ attached, (D), with 3 cap screws, one __M.I. Microscope and LS-50 assembly, (E)__, with 4 cap screws and 4 washers, one __C.D.Z., (F)__ with 4 cap screws and 4 washers, one R__iser assembly, (G)__, (2-Risers and one Riser Cross Bar), with 8 cap screws and 2 washers, __20 Alignment Pins, (H)__, and two hex wrenches 5mm and 6mm.
 +
 +[{{ ramm_assm_1.jpg?​direct&​300 |Fig 1}}]
 +
 +Step 2: Start with the two arches as shown in figure 2 placed the distance of a cross bar apart, (see figure 2). Add the two cross bars, (see figure 3a), that have cap screws only in their ends to the uppermost corner holes in the arches, (see figure 4a, b and c). The bars must have the mounting holes up and the smaller stage mounting holes to the inside, (see figure 5). Each bar needs four alignment pins and two cap screws, (as in figure 3b and 4a).
 +
 +[{{ ramm_assm_2.jpg?​direct&​300 |Fig 2}}]
 +
 +[{{ ramm_assm_3.jpg?​direct&​300 |Fig 3a}}]
 +
 +[{{ ramm_assm_4.jpg?​direct&​300 |Fig 3b}}]
 +
 +[{{ ramm_assm_5.jpg?​direct&​300 |Fig 4a,4b and 4c ; Click to Enlarge}}]
 +
 +[{{ ramm_assm_6.jpg?​direct&​300 |Fig 5: Top Bars on}}]
 +
 +Step 3: Add the next two cross bars with 2 extra cap screws to the upright arches at the second hole from the bottom. Use the same alignment pins on these bars and have the cap screws point down, (see figure 6 and 7a, b, and c).
 +
 +[{{ ramm_assm_7.jpg?​direct&​300 |Fig 6}}]
 +
 +[{{ ramm_assm_8.jpg?​direct&​300 |Fig 7a and 7b}}]
 +
 +[{{ ramm_assm_9.jpg?​direct&​300 |Fig 7c}}]
 +
 +Step 4: Add the alt cross bar and mount to the cap screws on the bottom of the lower bars.
 +
 +[{{ ramm_assm_10.jpg?​direct&​300 |Fig 7d}}]
 +
 +Step 5: Add the Modular Infinity Microscope to the alt cross bar and secure using the attached 4 cap screws and washers.
 +
 +[{{ ramm_assm_11.jpg?​direct&​300 |Fig 8a}}]
 +
 +[{{ ramm_assm_12.jpg?​direct&​300 |Fig 8b}}]
 +
 +[{{ ramm_assm_13.jpg?​direct&​300 |Fig 8c}}]
 +
 +Step 6: Add the Riser assembly to the top of the RAMM with the four alignment pins and the provided 6 cap screws, (as seen in figures 9 and 10).
 +
 +[{{ ramm_assm_14.jpg?​direct&​300 |Fig 9a and 9b}}]
 +
 +[{{ ramm_assm_15.jpg?​direct&​300 |Fig 10a}}]
 +
 +[{{ ramm_assm_16.jpg?​direct&​300 |Fig 10b}}]
 +
 +[{{ ramm_assm_17.jpg?​direct&​300 |Fig 10c}}]
 +
 +[{{ ramm_assm_18.jpg?​direct&​300 |Fig 10d}}]
 +
 +Step 7: Add the CDZ to the Riser assembly and center with the four cap screws, (as seen in figure 11 and 12).
 +
 +[{{ ramm_assm_19.jpg?​direct&​300 |Fig 11}}]
 +
 +[{{ ramm_assm_20.jpg?​direct&​300 |Fig 12}}]
 +
 +Step 8: Add the Ls-50 with dove tail to the CDZ and lock in place.
 +
 +[{{ ramm_assm_21.jpg?​direct&​300 |Fig 13}}]
 +
 +[{{ ramm_assm_22.jpg?​direct&​300 |Fig 14}}]
 +
 +Step 9: Mount the stage to the RAMM system with the supplied cap screws and connect the cables to the stage and both of the LS-50s.
 +
 +[{{ ramm_assm_23.jpg?​direct&​300 |Fig 15}}]
 +
 +[{{ ramm_assm_24.jpg?​direct&​300 |Fig 16}}]
 +
 +[{{ ramm_assm_25.jpg?​direct&​300 |Fig 17}}]
 +
 +{{tag>​ramm manual}}
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 + 
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
  
Address: 29391 W Enid Rd. Eugene, OR 97402, USA | Phone: +1 (541) 461-8181
assembly_instructions_for_ramm.txt · Last modified: 2019/04/18 23:33 (external edit)