User Tools

Site Tools


commands:pr

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
commands:pr [2018/06/20 17:52]
vik
commands:pr [2019/04/18 23:33] (current)
Line 1: Line 1:
 +====== Command:PR ======
  
 +This is a Tiger only command , that has different usage for MicroMirrors and Piezos
 +
 +--> MicroMirror#​
 +
 +^Shortcut ​ |PR| 
 +^Format ​ |PR [axis]=[5 to 10] …|
 +^Units ​   |Integer code, 5 to 10|
 +^Type    |Axis-Specific ​ |
 +^Remembered |Automatically |
 +^Firmware Required|v2.83+|
 +
 +This command is “recycled” for a different use in MicroMirror axes than for piezo. In the context of a MicroMirror axis this command is used to set the MicroMirror travel range. Settings is automatically saved into non-voltatile memory, however controller needs a system ''​RESET''​ or ''​RESTART''​ for setting to take effect.
 +
 +^PR[Axis Name] = ^MicroMirror Range \\ <wrap lo>in degrees</​wrap>​ ^
 +|5 |5|
 +|6 |6|
 +|8 \\ <wrap lo>​(default)</​wrap>​|8|
 +|10 |10|
 +
 +Example
 +<asi> $ PR A=5
 +:​A</​asi>​
 +Sets range of A axis as 5 degrees
 +<asi> $ PR A? B?
 +A=5 B=8 :​A</​asi>​
 +Queries the range of axes
 +
 +<--
 +
 +--> Piezo# ​
 +
 +^Shortcut ​ |PR| 
 +^Format ​ |PR [axis]=[0 to 8] …|
 +^Units ​   |Integer code, 0 to 8|
 +^Type    |Axis-Specific ​ |
 +^Remembered |Automatically |
 +
 +PR is used to set the piezo travel range. It is an Axis specific command. Setting is automatically saved in the non-volatile memory. Will need a system RESET or RESTART for setting to take effect.
 +
 +^PR [Axis Name] = ^Piezo Range \\ <wrap lo>in microns</​wrap>​ ^
 +|1 |50 ​  |
 +|2 |100 ​ |
 +|3 |150 ​ |
 +|4 |200 ​ |
 +|5 |300 ​ |
 +|6 |350 ​ |
 +|7 |500 ​ |
 +|8 |70 ​  |
 +
 +
 +<--
 +
 +--> Tunable Lens# 
 +
 +^Shortcut ​ |PR| 
 +^Format ​ |PR [axis]=[0 to 3] …|
 +^Units ​   |Integer code, 0 to 3|
 +^Type    |Axis-Specific ​ |
 +^Remembered |Automatically |
 +
 +PR is used to set the Tunable Lens units or user input. It is an Axis specific command. Setting is automatically saved in the non-volatile memory. Will need a system RESET or RESTART for setting to take effect. For more info refer to [[:​tiger_tunable_lens_card#​unitsresolution|Units/​Resolution]] section on TGTLC card page.
 +
 +^PR [Axis Name] = ^Units ^
 +|1 <wrap lo>​(default)</​wrap>​ |16bit integer, +32768 to -32768 ​   |
 +|2 |1/1000 of dpt, <wrap lo>range usually between 26000 to 7000</​wrap> ​ |
 +|3 |TBD <wrap lo>​reserved for future use</​wrap> ​ |
 +
 +
 +
 +<--
 +
 +
 +
 +
 +{{tag>​commands tiger piezo micromirror tlens}}
commands/pr.txt · Last modified: 2019/04/18 23:33 (external edit)