User Tools

Site Tools


gantry_translation_stage

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
gantry_translation_stage [2016/09/07 15:12]
asiadmin ↷ Page moved from documentation:gantry_translation_stage to gantry_translation_stage
gantry_translation_stage [2016/10/04 15:13] (current)
Line 38: Line 38:
 1) X/Y cable with DB25 Connector to the GTS-2000 Controller. 1) X/Y cable with DB25 Connector to the GTS-2000 Controller.
  
-{{ :​documentation:​gts_2_.jpg?​direct&​300 |}}   +{{ gts_2_.jpg?​direct&​300 |}}   
-{{ :​documentation:​gts_3_.jpg?​direct&​300 |}}   +{{ gts_3_.jpg?​direct&​300 |}}   
-{{ :​documentation:​gts_4_.jpg?​direct&​300 |}} +{{ gts_4_.jpg?​direct&​300 |}} 
-{{ :​documentation:​gts_5_.jpg?​direct&​300 |}}+{{ gts_5_.jpg?​direct&​300 |}}
  
 2) Z cable with DB15 Connector to the GTS Controller. ​ Note: Some systems may have and optional F Axis for zoom capability. 2) Z cable with DB15 Connector to the GTS Controller. ​ Note: Some systems may have and optional F Axis for zoom capability.
  
-{{ :​documentation:​gts_12.jpg?​direct&​300 |}}   +{{ gts_12.jpg?​direct&​300 |}}   
-{{ :​documentation:​gts_6_.jpg?​direct&​300 |}} +{{ gts_6_.jpg?​direct&​300 |}} 
-{{ :​documentation:​gts_7_.jpg?​direct&​300 |}}   +{{ gts_7_.jpg?​direct&​300 |}}   
-{{ :​documentation:​gts_8_.jpg?​direct&​300 |}}+{{ gts_8_.jpg?​direct&​300 |}}
  
 3) Attach the X,Y,& Z Connectors to the GTS as shown in the photo below. 3) Attach the X,Y,& Z Connectors to the GTS as shown in the photo below.
  
-{{ :​documentation:​gts_new_2_.png?​direct&​300 |}}+{{ gts_new_2_.png?​direct&​300 |}}
  
 4) Connect the 24V DC 2.7A power power supply to back of the  GTS controller. 4) Connect the 24V DC 2.7A power power supply to back of the  GTS controller.
Line 69: Line 69:
 To adjust the Y Limit switches –locate the two limit switches on the  Y(tray) axis.    ​ To adjust the Y Limit switches –locate the two limit switches on the  Y(tray) axis.    ​
  
-{{ :​documentation:​gts_new_3_.png?​direct&​300 |}}+{{ gts_new_3_.png?​direct&​300 |}}
  
-{{ :​documentation:​gts_new_5_.jpg?​direct&​300 |}}+{{ gts_new_5_.jpg?​direct&​300 |}}
  
-{{ :​documentation:​gts_new_4_.jpg?​direct&​300 |}}+{{ gts_new_4_.jpg?​direct&​300 |}}
  
 Figure 5 below shows one of the limit switch magnets, which can be moved along the rail after loosening its locking set screw with  a 0.050 Allen wrench. ​ To reduce the range of travel, move the magnets inward toward the center of the sample tray. Figure 5 below shows one of the limit switch magnets, which can be moved along the rail after loosening its locking set screw with  a 0.050 Allen wrench. ​ To reduce the range of travel, move the magnets inward toward the center of the sample tray.
  
-[{{ :​documentation:​gts_new_4_.png?​direct&​300 |Figure 5: Adjusting a Y-axis Limit Switch}}]+[{{ gts_new_4_.png?​direct&​300 |Figure 5: Adjusting a Y-axis Limit Switch}}]
  
  
Line 87: Line 87:
 To adjust the X Limit switches, locate the two limit switches on the X (gantry) axis.    ​ To adjust the X Limit switches, locate the two limit switches on the X (gantry) axis.    ​
  
-{{ :​documentation:​gts_new_5_.png?​direct&​300 |}} +{{ gts_new_5_.png?​direct&​300 |}} 
  
 Just as done with the Y axis, the X axis limit switch magnets can be moved along the rail after loosening its locking set screw with  a 0.050 Allen wrench. ​ To reduce the range of travel, move the magnets inward toward the center of the gantry bar. Just as done with the Y axis, the X axis limit switch magnets can be moved along the rail after loosening its locking set screw with  a 0.050 Allen wrench. ​ To reduce the range of travel, move the magnets inward toward the center of the gantry bar.
  
-{{ :​documentation:​gts_new_1_.png?​direct&​300 |}}+{{ gts_new_1_.png?​direct&​300 |}}
  
-{{ :​documentation:​gts_new_1_.jpg?​direct&​300 |}}+{{ gts_new_1_.jpg?​direct&​300 |}}
  
 Check the operation of the limit switch by slowly moving the stage toward the end of travel. ​ When a limit is reached, the motion will be terminated and the letter “U” or “L” will appear on the LCD screen showing that the limit is in force Check the operation of the limit switch by slowly moving the stage toward the end of travel. ​ When a limit is reached, the motion will be terminated and the letter “U” or “L” will appear on the LCD screen showing that the limit is in force
Line 99: Line 99:
 ===== GTS Operation ​ ===== ===== GTS Operation ​ =====
  
-Refer to [[documentation:​ms2000_operation|MS2000 OPERATION]] on how to setup and use the MS2000 controller with the GTS system.+Refer to [[ms2000_operation|MS2000 OPERATION]] on how to setup and use the MS2000 controller with the GTS system.
  
    
Line 111: Line 111:
 To lubricate the Y-axis lead screw, it is necessary to remove the stage (and the optional light table, if applicable). ​ This procedure is outlined in figure 10. To lubricate the Y-axis lead screw, it is necessary to remove the stage (and the optional light table, if applicable). ​ This procedure is outlined in figure 10.
  
-[{{ :​documentation:​gts_1_.jpg?​direct&​300 |Figure 10:  Remove the coupling screws}}]+[{{ gts_1_.jpg?​direct&​300 |Figure 10:  Remove the coupling screws}}]
  
  
gantry_translation_stage.txt · Last modified: 2016/10/04 15:13 (external edit)