User Tools

Site Tools


leica_dm4000_dm6000_zdrive

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
leica_dm4000_dm6000_zdrive [2016/09/07 15:12]
asiadmin ↷ Page moved from documentation:leica_dm4000_dm6000_zdrive to leica_dm4000_dm6000_zdrive
leica_dm4000_dm6000_zdrive [2016/10/04 15:13] (current)
Line 17: Line 17:
 ===== Part 1 - Removing the Left Fine Focus Knob ===== ===== Part 1 - Removing the Left Fine Focus Knob =====
  
-[{{ :​documentation:​dm4000.png?​direct&​300 |Figure 1:  Use 1.5 mm Allen wrench to loosen setscrew to remove knob.}}]+[{{ dm4000.png?​direct&​300 |Figure 1:  Use 1.5 mm Allen wrench to loosen setscrew to remove knob.}}]
  
-[{{ :​documentation:​dm4000_2.png?​direct&​300 |Figure 2:  Pull knob straight off to expose shaft – Do not twist.}}]+[{{ dm4000_2.png?​direct&​300 |Figure 2:  Pull knob straight off to expose shaft – Do not twist.}}]
  
 a) Use 1.5 mm Allen wrench to loosen setscrew to remove knob. \\ a) Use 1.5 mm Allen wrench to loosen setscrew to remove knob. \\
 b) Pull knob straight off to expose shaft – Do not twist b) Pull knob straight off to expose shaft – Do not twist
    
-[{{ :​documentation:​dm4000_3.png?​direct&​300 |Figures 3a}}]+[{{ dm4000_3.png?​direct&​300 |Figures 3a}}]
  
-[{{ :​documentation:​dm4000_4.png?​direct&​300 |Figures 3b:  Locate Brass coupler and install it over the white tab as shown. ​ Use Allen wrench to tighten setscrew to secure brass coupler in place}}]+[{{ dm4000_4.png?​direct&​300 |Figures 3b:  Locate Brass coupler and install it over the white tab as shown. ​ Use Allen wrench to tighten setscrew to secure brass coupler in place}}]
  
 c) Locate Brass coupler and install it over the white tab as shown. ​ Use Allen wrench to tighten setscrew to secure brass coupler in place. ​ Please note that if white gear with tab slides away from the inner gear that it engages then the stage will slip down.  This will not harm the microscope. ​ Simply slide the gear back on so that it fully engages the inner gear and install thebrass coupler as show. c) Locate Brass coupler and install it over the white tab as shown. ​ Use Allen wrench to tighten setscrew to secure brass coupler in place. ​ Please note that if white gear with tab slides away from the inner gear that it engages then the stage will slip down.  This will not harm the microscope. ​ Simply slide the gear back on so that it fully engages the inner gear and install thebrass coupler as show.
Line 32: Line 32:
 ===== Part 2 - Installing the Baseplate ===== ===== Part 2 - Installing the Baseplate =====
  
-[{{ :​documentation:​dm4000_5.png?​direct&​300 |Figure 4:  Remove screw}}]+[{{ dm4000_5.png?​direct&​300 |Figure 4:  Remove screw}}]
  
-[{{ :​documentation:​dm4000_6.png?​direct&​300 |Figure 5:  Center plate under focus knob.  }}]+[{{ dm4000_6.png?​direct&​300 |Figure 5:  Center plate under focus knob.  }}]
  
 Locate the base plate, and if the Z-drive is attached to it as shown in figure 4, use the 7/64” Allen wrench to remove the horizontal adjustment screw that secures it to the base plate. ​ Lift the front of the microscope up and slide the baseplate under the microscope so that the unit is centered under the left focus knob as shown in figure 5. Locate the base plate, and if the Z-drive is attached to it as shown in figure 4, use the 7/64” Allen wrench to remove the horizontal adjustment screw that secures it to the base plate. ​ Lift the front of the microscope up and slide the baseplate under the microscope so that the unit is centered under the left focus knob as shown in figure 5.
Line 40: Line 40:
 ===== Part-3 - Installing and Aligning the Motor Drive ===== ===== Part-3 - Installing and Aligning the Motor Drive =====
  
-[{{ :​documentation:​dm4000_7.png?​direct&​300 |Figure 6:  Location of vertical adjustment screws}}]+[{{ dm4000_7.png?​direct&​300 |Figure 6:  Location of vertical adjustment screws}}]
  
-[{{ :​documentation:​dm4000_8.png?​direct&​300 |Figure 7: Installing the Z-drive.}}]+[{{ dm4000_8.png?​direct&​300 |Figure 7: Installing the Z-drive.}}]
  
-[{{ :​documentation:​dm4000_9.png?​direct&​300 |Figure 8:  Tightening the Z-drive clamp}}]+[{{ dm4000_9.png?​direct&​300 |Figure 8:  Tightening the Z-drive clamp}}]
  
 a) Locate the ASI fine focus motor drive and loosen the two vertical adjustment screws that secure the drive to the adjustment bar.  (See figure 6 for location of the two vertical adjustment screws.) ​ Using the 7/​64"​hex wrench, loosen the screws just enough so that the drive can slide easily in the groove in the adjustment bar. a) Locate the ASI fine focus motor drive and loosen the two vertical adjustment screws that secure the drive to the adjustment bar.  (See figure 6 for location of the two vertical adjustment screws.) ​ Using the 7/​64"​hex wrench, loosen the screws just enough so that the drive can slide easily in the groove in the adjustment bar.
Line 52: Line 52:
 c) Rotate the drive so that the tab on the bottom of the adjustment bar fits into the groove on the baseplate. ​ Install, but do not completely tighten, the vertical adjustment screw (figure 9) to hold the drive in place. ​ Please Note:  the baseplate may need to be moved to properly align the adjustment bar. c) Rotate the drive so that the tab on the bottom of the adjustment bar fits into the groove on the baseplate. ​ Install, but do not completely tighten, the vertical adjustment screw (figure 9) to hold the drive in place. ​ Please Note:  the baseplate may need to be moved to properly align the adjustment bar.
  
-[{{ :​documentation:​dm4000_10.png?​direct&​300 |Figure 9:  Horizontal Adjustment screw}}]+[{{ dm4000_10.png?​direct&​300 |Figure 9:  Horizontal Adjustment screw}}]
  
-[{{ :​documentation:​dm4000_11.png?​direct&​300 |Figure 10:  Vertical Adjustment screws}}]+[{{ dm4000_11.png?​direct&​300 |Figure 10:  Vertical Adjustment screws}}]
  
  
 d) Slide the motor drive up and down, forward and backward slightly while turning the right fine focus knob until it is in the position where minimum drag is felt on the right focus knob.  Secure the motor drive into position by tightening the horizontal and vertical adjustment screws. d) Slide the motor drive up and down, forward and backward slightly while turning the right fine focus knob until it is in the position where minimum drag is felt on the right focus knob.  Secure the motor drive into position by tightening the horizontal and vertical adjustment screws.
  
-[{{ :​documentation:​dm4000_12.png?​direct&​300 |Figure 11:  Tighten Baseplate set screw}}]+[{{ dm4000_12.png?​direct&​300 |Figure 11:  Tighten Baseplate set screw}}]
  
  
Line 67: Line 67:
 ===== Part 4 - Installing the Motor Drive Cover Plate and Fine Focus Knob ===== ===== Part 4 - Installing the Motor Drive Cover Plate and Fine Focus Knob =====
  
-{{ :​documentation:​dm4000_13.png?​direct&​300 |Figure 12}}+{{ dm4000_13.png?​direct&​300 |Figure 12}}
  
-{{ :​documentation:​dm4000_14.png?​direct&​300 |Figure 13: Installing cover and focus knob}}+{{ dm4000_14.png?​direct&​300 |Figure 13: Installing cover and focus knob}}
  
 a) Locate the motor drive cover. ​ Remove the 4/40 button head screws from the baseplate with the 1/16” Allen wrench. ​ Position the motor drive cover over the motor drive assembly and secure in place using the 4/40 button head screws. a) Locate the motor drive cover. ​ Remove the 4/40 button head screws from the baseplate with the 1/16” Allen wrench. ​ Position the motor drive cover over the motor drive assembly and secure in place using the 4/40 button head screws.
leica_dm4000_dm6000_zdrive.txt · Last modified: 2016/10/04 15:13 (external edit)