User Tools

Site Tools


leica_dmil_zdrive

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
leica_dmil_zdrive [2016/09/07 22:12]
asiadmin ↷ Page moved from documentation:leica_dmil_zdrive to leica_dmil_zdrive
leica_dmil_zdrive [2016/10/04 22:13] (current)
Line 21: Line 21:
 Remove the left fine focus knob from the microscope as follows:  ​ Remove the left fine focus knob from the microscope as follows:  ​
  
-[{{ :​documentation:​dmil_1.png?​direct&​300 |Figure 1a}}]+[{{ dmil_1.png?​direct&​300 |Figure 1a}}]
  
-[{{ :​documentation:​dmil_2.png?​direct&​300 |Figure 1b}}]+[{{ dmil_2.png?​direct&​300 |Figure 1b}}]
  
-[{{ :​documentation:​dmil_3.png?​direct&​300 |Figure 1c}}]+[{{ dmil_3.png?​direct&​300 |Figure 1c}}]
                
 a) Locate small hole on knob. a) Locate small hole on knob.
Line 36: Line 36:
 ===== Part 2 - Installing the Baseplate ===== ===== Part 2 - Installing the Baseplate =====
  
-[{{ :​documentation:​dmil_4.png?​direct&​300 |Figure 2a}} ]+[{{ dmil_4.png?​direct&​300 |Figure 2a}} ]
  
-[{{ :​documentation:​dmil_5.png?​direct&​300 |Figure 2b}}]+[{{ dmil_5.png?​direct&​300 |Figure 2b}}]
                 ​                 ​
 a) Locate the two parts baseplate and adjustment bar and assemble if as shown in figure 2a (may already be assembled). a) Locate the two parts baseplate and adjustment bar and assemble if as shown in figure 2a (may already be assembled).
Line 48: Line 48:
 d) Use a 3mm allen wrench to slightly loosen two baseplate vertical adjust screws to allow for aligning Z-Drive unit.   ​Loosen the screw just enough so that the adjustment bar can slide easily. d) Use a 3mm allen wrench to slightly loosen two baseplate vertical adjust screws to allow for aligning Z-Drive unit.   ​Loosen the screw just enough so that the adjustment bar can slide easily.
  
-[{{ :​documentation:​dmil_6.png?​direct&​300 |Figure 2c  }}]+[{{ dmil_6.png?​direct&​300 |Figure 2c  }}]
  
-[{{ :​documentation:​dmil_7.png?​direct&​300 |Figure 2d}}]+[{{ dmil_7.png?​direct&​300 |Figure 2d}}]
  
 ===== Part-3 Installing ​ the Motor Drive ===== ===== Part-3 Installing ​ the Motor Drive =====
  
-{{ :​documentation:​dmil_8.png?​direct&​300 |Figure 3a}}+{{ dmil_8.png?​direct&​300 |Figure 3a}}
  
-{{ :​documentation:​dmil_9.png?​direct&​300 |Figure 3b}}+{{ dmil_9.png?​direct&​300 |Figure 3b}}
  
-{{ :​documentation:​dmil_10.png?​direct&​300 |Figure 3c}}+{{ dmil_10.png?​direct&​300 |Figure 3c}}
  
 a) Locate the Tab on the bottom of the Z-Drive Alignment Arm,  this will eventually go into the slot on the Baseplate (Figures 3a & 3b). a) Locate the Tab on the bottom of the Z-Drive Alignment Arm,  this will eventually go into the slot on the Baseplate (Figures 3a & 3b).
Line 70: Line 70:
 e) Attach the Z-Drive adjustment bar to the baseplate using the 4mm socket head horizontal adjustment screw with the 3mm hex wrench. ​       The horizontal screw should be tightened till the adjustment bar tab will easily slide in the slot in the baseplate. e) Attach the Z-Drive adjustment bar to the baseplate using the 4mm socket head horizontal adjustment screw with the 3mm hex wrench. ​       The horizontal screw should be tightened till the adjustment bar tab will easily slide in the slot in the baseplate.
  
-[{{ :​documentation:​dmil_11.png?​direct&​300 |Figure 3d}}]+[{{ dmil_11.png?​direct&​300 |Figure 3d}}]
  
-[{{ :​documentation:​dmil_12.png?​direct&​300 |Figure 3e}}]+[{{ dmil_12.png?​direct&​300 |Figure 3e}}]
  ​  ​  ​  ​
   
Line 78: Line 78:
 ===== Part-4 Aligning ​ the Motor Drive ===== ===== Part-4 Aligning ​ the Motor Drive =====
  
-[{{ :​documentation:​dmil_13.png?​direct&​300 |Figure 4a}}]+[{{ dmil_13.png?​direct&​300 |Figure 4a}}]
  
-[{{ :​documentation:​dmil_14.png?​direct&​300 |Figure 4b}}]+[{{ dmil_14.png?​direct&​300 |Figure 4b}}]
  
-[{{ :​documentation:​dmil_15.png?​direct&​300 |Figure 4c}}]+[{{ dmil_15.png?​direct&​300 |Figure 4c}}]
     
   
Line 96: Line 96:
 e) Tighten the set screws on the flex couplers using a 2mm hex driver as shown in figure 4e.  Double check and ensure that the vertical / horizontal alignment screws, and baseplate set screw are tight. e) Tighten the set screws on the flex couplers using a 2mm hex driver as shown in figure 4e.  Double check and ensure that the vertical / horizontal alignment screws, and baseplate set screw are tight.
  
-[{{ :​documentation:​dmil_16.png?​direct&​300 |Figure 4d}}]+[{{ dmil_16.png?​direct&​300 |Figure 4d}}]
  
-[{{ :​documentation:​dmil_17.png?​direct&​300 |Figure 4e}}]+[{{ dmil_17.png?​direct&​300 |Figure 4e}}]
  ​  ​  ​  ​
   
Line 104: Line 104:
 ===== Part 5-Installing the motor drive cover plate & fine focus knob. ===== ===== Part 5-Installing the motor drive cover plate & fine focus knob. =====
   
-[{{ :​documentation:​dmil_18.png?​direct&​300 |Figure 5a}}]+[{{ dmil_18.png?​direct&​300 |Figure 5a}}]
  
-[{{ :​documentation:​dmil_19.png?​direct&​300 |Figure 5b}}]+[{{ dmil_19.png?​direct&​300 |Figure 5b}}]
  
-[{{ :​documentation:​dmil_20.png?​direct&​300 |Figure 5c}}]+[{{ dmil_20.png?​direct&​300 |Figure 5c}}]
  
 a) Locate the motor drive cover and the 2 3mm button head screws shown in figure 5a.   You might have to remove the 2 screws from the baseplate holes. ​   Place the cover over the motor drive. a) Locate the motor drive cover and the 2 3mm button head screws shown in figure 5a.   You might have to remove the 2 screws from the baseplate holes. ​   Place the cover over the motor drive.
Line 120: Line 120:
 e) Use the  1.5mm screwdriver to tighten the knob set screw as shown on figure 5e.  e) Use the  1.5mm screwdriver to tighten the knob set screw as shown on figure 5e. 
  
-[{{ :​documentation:​dmil_21.png?​direct&​300 |Figure 5d}}]+[{{ dmil_21.png?​direct&​300 |Figure 5d}}]
  
-[{{ :​documentation:​dmil_22.png?​direct&​300 |Figure 5e}}]+[{{ dmil_22.png?​direct&​300 |Figure 5e}}]
      
 This completes the procedure for installing the ASI motor drive on to the Leica DMIL Microscope. This completes the procedure for installing the ASI motor drive on to the Leica DMIL Microscope.
  
 {{tag>​leica DMIL zdrive}} {{tag>​leica DMIL zdrive}}
leica_dmil_zdrive.txt · Last modified: 2016/10/04 22:13 (external edit)