nikon_mm800_zdrive_install
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
nikon_mm800_zdrive_install [2016/11/04 14:50] – vik | nikon_mm800_zdrive_install [2021/09/23 17:15] (current) – external edit 127.0.0.1 | ||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ====== Nikon MM-800 Left-Hand Z-Drive Installation Procedure ====== | ||
+ | The procedure below outlines the steps necessary to install the ASI Microscope Focus Controller Drive onto the Nikon MM-800 microscope. | ||
+ | |||
+ | {{ :: | ||
+ | |||
+ | == To perform the following steps, you will need the following tools == | ||
+ | |||
+ | * Small cross blade screwdriver | ||
+ | * 3mm Allen Wrenches | ||
+ | * 1.5mm Allen Wrenches | ||
+ | * 1.3mm Allen Wrenches | ||
+ | * 7/64 Allen Wrenches | ||
+ | * 1/16 Allen Wrenches | ||
+ | * Need 2 mm x 8 mm socket head cap screws for attaching drive | ||
+ | |||
+ | //The Allen hex wrenches, and screws are provided by ASI// | ||
+ | |||
+ | == The procedure has three parts == | ||
+ | |||
+ | |||
+ | - Removing the left fine focus knob & cover plate assembly. | ||
+ | - Installing the clutch plate. | ||
+ | - Installing and aligning the motor drive assembly. | ||
+ | - Installing the motor drive cover plate and fine focus knob. | ||
+ | |||
+ | ===== Part 1 & 2 - Removing the Left Fine Focus Knob and Installing the Clutch Plate ===== | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | As shown in figures 1 though 6 remove the cover and fine focus knob from the left side of the focus assembly. | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | Locate the brass clutch plate shown in figure 7 and install it onto the fine focus shaft as shown in figures 8 & 9. Insure the plate is pressed completely onto the focus shaft & that the setscrew is securely tightened to hold the plate onto the fine focus shaft. | ||
+ | |||
+ | ===== Part 2 & 3 - Installing the Baseplate and Aligning the Motor Drive ===== | ||
+ | |||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | |||
+ | ===== Part 4 Installing the motor drive cover plate and fine focus knob ===== | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | [{{ :: | ||
+ | |||
+ | This completes the procedure for installing the ASI focus drive on to the Nikon MM-800 microscope. | ||
+ | |||
+ | {{tag> |
Address: 29391 W Enid Rd. Eugene, OR 97402, USA | Phone: +1 (541) 461-8181
nikon_mm800_zdrive_install.txt · Last modified: 2021/09/23 17:15 by 127.0.0.1