User Tools

Site Tools


nikon_te2000_right_zdrive

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
nikon_te2000_right_zdrive [2016/05/19 16:15]
vik
nikon_te2000_right_zdrive [2016/10/04 15:13] (current)
Line 20: Line 20:
 Remove the right fine focus knob from the microscope as follows:  ​ Remove the right fine focus knob from the microscope as follows:  ​
  
-[{{ :​documentation:​te2000_right.png?​direct&​300 |Figure 1: Use screwdriver to remove two screws }}]+[{{ te2000_right.png?​direct&​300 |Figure 1: Use screwdriver to remove two screws }}]
  
-[{{ :​documentation:​te2000_right_2.png?​direct&​300 |Figure 2: Pull knob straight off to expose brass adapter screws &  remove brass adapter plate.}}]+[{{ te2000_right_2.png?​direct&​300 |Figure 2: Pull knob straight off to expose brass adapter screws &  remove brass adapter plate.}}]
  
 Use screwdriver to remove two screws. Remove the fine focus knob by grasping it firmly and Use screwdriver to remove two screws. Remove the fine focus knob by grasping it firmly and
Line 31: Line 31:
 ===== Part 2 - Installing the Baseplate ===== ===== Part 2 - Installing the Baseplate =====
    
-[{{ :​documentation:​te2000_right_3.png?​direct&​300 |Figure 3: Installed baseplate}}]+[{{ te2000_right_3.png?​direct&​300 |Figure 3: Installed baseplate}}]
  
-[{{ :​documentation:​te2000_right_4.png?​direct&​300 |Figure 4: Baseplate clearance holes }}]+[{{ te2000_right_4.png?​direct&​300 |Figure 4: Baseplate clearance holes }}]
  
-[{{ :​documentation:​te2000_right_5.png?​direct&​300 |Figure 5: Baseplate clamp }}]+[{{ te2000_right_5.png?​direct&​300 |Figure 5: Baseplate clamp }}]
  
 Locate the baseplate. ​ If the motor drive is attached to the base plate use the 3mm Allen wrench to remove the horizontal adjustment screw to remove the drive from the base plate. ​ Position the base plate so that the large baseplate is on the right side of the microscope. Lift the front of the microscope up and slide the baseplate under the microscope so that the horizontal adjustment bar is centered under the right focus knob as shown in figure # 3. There are two clearance holes, as shown in figure # 4, for two screws on the bottom of the microscope. ​ When the baseplate is "​about"​ in the correct position you will feel the screw drop into the holes. Leave the clamp shown in figure # 5 loose at this time. Locate the baseplate. ​ If the motor drive is attached to the base plate use the 3mm Allen wrench to remove the horizontal adjustment screw to remove the drive from the base plate. ​ Position the base plate so that the large baseplate is on the right side of the microscope. Lift the front of the microscope up and slide the baseplate under the microscope so that the horizontal adjustment bar is centered under the right focus knob as shown in figure # 3. There are two clearance holes, as shown in figure # 4, for two screws on the bottom of the microscope. ​ When the baseplate is "​about"​ in the correct position you will feel the screw drop into the holes. Leave the clamp shown in figure # 5 loose at this time.
Line 41: Line 41:
 ===== Part-3 Installing & Aligning the Motor Drive ===== ===== Part-3 Installing & Aligning the Motor Drive =====
  
-[{{ :​documentation:​te2000_right_6.png?​direct&​300 |Figure 6 Loosen Vertical adjustment screws }}]+[{{ te2000_right_6.png?​direct&​300 |Figure 6 Loosen Vertical adjustment screws }}]
    
-[{{ :​documentation:​te2000_right_7.png?​direct&​300 |Figure 7 Install Z-drive over fine focus shaft }}]+[{{ te2000_right_7.png?​direct&​300 |Figure 7 Install Z-drive over fine focus shaft }}]
  
-[{{ :​documentation:​te2000_right_8.png?​direct&​300 |Figure 8 Press clamp against washer & tighten clamp securely to attach drive. }}]+[{{ te2000_right_8.png?​direct&​300 |Figure 8 Press clamp against washer & tighten clamp securely to attach drive. }}]
  
 Loosen the two Vertical screws that secure the drive to the adjustment bar as shown in figure #6. Loosen the two Vertical screws that secure the drive to the adjustment bar as shown in figure #6.
Line 55: Line 55:
 Rotate the drive so that the tab on the bottom of the adjustment bar fits into the grove on the base plate. Install, but do not completely tighten the vertical adjustment screw ( figure # 9 )  to hold the drive in place. Please Note the baseplate may need to be moved to properly align the adjustment bar. Press the clamp all of the way against the washers as shown in figure 8.  The clamp must depress the wave washer completely as shown. When the clamp & drive are properly aligned use the 7/64" Allen  wrench to securely tighten the drive shaft clamp as shown in figure # 8 Rotate the drive so that the tab on the bottom of the adjustment bar fits into the grove on the base plate. Install, but do not completely tighten the vertical adjustment screw ( figure # 9 )  to hold the drive in place. Please Note the baseplate may need to be moved to properly align the adjustment bar. Press the clamp all of the way against the washers as shown in figure 8.  The clamp must depress the wave washer completely as shown. When the clamp & drive are properly aligned use the 7/64" Allen  wrench to securely tighten the drive shaft clamp as shown in figure # 8
  
-[{{ :​documentation:​te2000_right_9.png?​direct&​300 |Figure 9 Horizontal Adjustment screw }}]+[{{ te2000_right_9.png?​direct&​300 |Figure 9 Horizontal Adjustment screw }}]
  
-[{{ :​documentation:​te2000_right_10.png?​direct&​300 |Figure 10 Tightening the base plate clamp }}]+[{{ te2000_right_10.png?​direct&​300 |Figure 10 Tightening the base plate clamp }}]
  
 Slide the motor drive up and down, forward and backward slightly while turning the right fine focus knob until it is in the position where minimum drag is felt on the right focus knob. Slide the motor drive up and down, forward and backward slightly while turning the right fine focus knob until it is in the position where minimum drag is felt on the right focus knob.
Line 69: Line 69:
 ===== Part 4-Installing the motor drive cover plate & fne focus knob. ===== ===== Part 4-Installing the motor drive cover plate & fne focus knob. =====
  
-[{{ :​documentation:​te2000_right_11.png?​direct&​300 |Figure 11 Installing cover }}]+[{{ te2000_right_11.png?​direct&​300 |Figure 11 Installing cover }}]
  
-[{{ :​documentation:​te2000_right_12.png?​direct&​300 |Figure 12 Installing brass knob adapter }}]+[{{ te2000_right_12.png?​direct&​300 |Figure 12 Installing brass knob adapter }}]
   
 Locate the motor drive cover. Remove the 4/40 button head screws from the base plate with the 1/16” Allen wrench. Position the motor drive covert over the motor drive assembly and secure in place using the 4/40 button head screws as shown in figure # 11. Slide the microscope brass knob adapter over the shaft extension and press it on all the way. Secure it in place by tightening the to set screws. ​ Install the knob onto the brass adapter plate. Locate the motor drive cover. Remove the 4/40 button head screws from the base plate with the 1/16” Allen wrench. Position the motor drive covert over the motor drive assembly and secure in place using the 4/40 button head screws as shown in figure # 11. Slide the microscope brass knob adapter over the shaft extension and press it on all the way. Secure it in place by tightening the to set screws. ​ Install the knob onto the brass adapter plate.
nikon_te2000_right_zdrive.txt · Last modified: 2016/10/04 15:13 (external edit)