User Tools

Site Tools


oly_bh2_zdrive_installation

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
oly_bh2_zdrive_installation [2016/09/07 15:26]
asiadmin ↷ Page moved from documentation:oly_bh2_zdrive_installation to oly_bh2_zdrive_installation
oly_bh2_zdrive_installation [2016/10/04 15:13] (current)
Line 26: Line 26:
 </​WRAP>​ </​WRAP>​
  
-{{ :​documentation:​bh2_2_.jpg?​direct&​300 |}}+{{ bh2_2_.jpg?​direct&​300 |}}
  
 1) Carefully slip the knife point into the inside edge of the left fine focus knob end and pry out the 20mm black disk that covers the fine focus knob attachment screw. 1) Carefully slip the knife point into the inside edge of the left fine focus knob end and pry out the 20mm black disk that covers the fine focus knob attachment screw.
  
-{{ :​documentation:​bh2_3_.jpg?​direct&​300 |}}+{{ bh2_3_.jpg?​direct&​300 |}}
      
 2) Remove the left fine focus knob by first removing the attachment screw using the 2.5mm hex wrench then pulling the knob off of the fine focus shaft. It will be necessary to hold the right fine focus knob while removing the screw to prevent the shaft from turning. ​ 2) Remove the left fine focus knob by first removing the attachment screw using the 2.5mm hex wrench then pulling the knob off of the fine focus shaft. It will be necessary to hold the right fine focus knob while removing the screw to prevent the shaft from turning. ​
  
-{{ :​documentation:​bh2_washer.jpg?​direct&​300 |}}+{{ bh2_washer.jpg?​direct&​300 |}}
  
 3) After the knob has been removed insure that the wave washer is still located on the brass clutch assembly on the focus shaft. ​ If the washer has stuck to the fine focus knob that was removed place it as shown on to the focus shaft. 3) After the knob has been removed insure that the wave washer is still located on the brass clutch assembly on the focus shaft. ​ If the washer has stuck to the fine focus knob that was removed place it as shown on to the focus shaft.
Line 43: Line 43:
 Locate the motor drive, the back plate and the brass clutch plate.  ​ Locate the motor drive, the back plate and the brass clutch plate.  ​
  
-[{{ :​documentation:​bh2_5_.jpg?​direct&​300 |Back Plate}}]+[{{ bh2_5_.jpg?​direct&​300 |Back Plate}}]
  
-[{{ :​documentation:​bh2_6_.jpg?​direct&​300 |Drive Assembly}}]+[{{ bh2_6_.jpg?​direct&​300 |Drive Assembly}}]
             ​             ​
 In this step we will install the ASI backplate and motor drive assembly as a unit. The ASI backplate will be installed and clamped to the back of the microscope as shown only after the motor drive is clamped onto the fine focus shaft of the microscope. Before installing the backplate and drive assembly loosen but do not remove the horizontal and vertical adjustment screws. When these screws are loosened the motor drive should move freely about in the horizontal and vertical adjustment axis. In this step we will install the ASI backplate and motor drive assembly as a unit. The ASI backplate will be installed and clamped to the back of the microscope as shown only after the motor drive is clamped onto the fine focus shaft of the microscope. Before installing the backplate and drive assembly loosen but do not remove the horizontal and vertical adjustment screws. When these screws are loosened the motor drive should move freely about in the horizontal and vertical adjustment axis.
Line 52: Line 52:
  
  
-[{{ :​documentation:​bh2_7_.jpg?​direct&​300 |Horizontal adjustment screw}}]+[{{ bh2_7_.jpg?​direct&​300 |Horizontal adjustment screw}}]
  
-[{{ :​documentation:​bh2_8_.jpg?​direct&​300 |Vertical adjustment screws}}]+[{{ bh2_8_.jpg?​direct&​300 |Vertical adjustment screws}}]
  
 ===== Installing the Drive & Brass Clutch Plate ===== ===== Installing the Drive & Brass Clutch Plate =====
Line 63: Line 63:
 ** **
  
-[{{ :​documentation:​bh2_9_.jpg?​direct&​300 |Slide ASI drive over fine focus shaft}}]+[{{ bh2_9_.jpg?​direct&​300 |Slide ASI drive over fine focus shaft}}]
  
-[{{ :​documentation:​bh2_10_.jpg?​direct&​300 |Press clamp & clutch plate firmly against microscope}}]+[{{ bh2_10_.jpg?​direct&​300 |Press clamp & clutch plate firmly against microscope}}]
                    
-[{{ :​documentation:​bh2_11_.jpg?​direct&​300 |Securely Tighten Clamp }}]+[{{ bh2_11_.jpg?​direct&​300 |Securely Tighten Clamp }}]
    ​  ​    ​  ​
-[{{ :​documentation:​bh2_12_.jpg?​direct&​300 |Clutch & Drive Securely Tightened}}]+[{{ bh2_12_.jpg?​direct&​300 |Clutch & Drive Securely Tightened}}]
  
 ===== Aligning the drive ===== ===== Aligning the drive =====
Line 75: Line 75:
 After installing & securing the drive and brass clutch plate to the focus shaft of the microscope the back plate can be positioned and secured. ​ Position the back plate to a point midway along the slots for the two vertical adjustment screws and secure it in place by tightening the set screw to depress the clamp on side of the microscope. After installing & securing the drive and brass clutch plate to the focus shaft of the microscope the back plate can be positioned and secured. ​ Position the back plate to a point midway along the slots for the two vertical adjustment screws and secure it in place by tightening the set screw to depress the clamp on side of the microscope.
  
-[{{ :​documentation:​bh2_13_.jpg?​direct&​300 |Position back plate so that vertical adjustment screws are midway in slots}}]+[{{ bh2_13_.jpg?​direct&​300 |Position back plate so that vertical adjustment screws are midway in slots}}]
  ​  ​  ​  ​
-{{ :​documentation:​bh2_14_.jpg?​direct&​300 |}}+{{ bh2_14_.jpg?​direct&​300 |}}
 Use the 5/64” Allen Wrench to tighten the Base plate clamp at a point where the vertical adjustment screws are midway in the slots Use the 5/64” Allen Wrench to tighten the Base plate clamp at a point where the vertical adjustment screws are midway in the slots
  
Line 87: Line 87:
 ===== Step 6 - Installing the cover & left fine focus knob ===== ===== Step 6 - Installing the cover & left fine focus knob =====
  
-{{ :​documentation:​bh2_1_.jpg?​direct&​300 |}}+{{ bh2_1_.jpg?​direct&​300 |}}
  
 Remove the two screws from the edges of the drive assembly. Locate the ASI cover plate. Place it in position over the motor drive assembly and secure it with the screws just removed. Place the left fine focus knob over the protruding end of the drive shaft and secure it in place with the original screw using the 2.5 mm allen wrench. Install the 20mm black disk that covers the fine focus knob attachment screw. ​ This 20mm black disk was removed in step #1. Remove the two screws from the edges of the drive assembly. Locate the ASI cover plate. Place it in position over the motor drive assembly and secure it with the screws just removed. Place the left fine focus knob over the protruding end of the drive shaft and secure it in place with the original screw using the 2.5 mm allen wrench. Install the 20mm black disk that covers the fine focus knob attachment screw. ​ This 20mm black disk was removed in step #1.
oly_bh2_zdrive_installation.txt · Last modified: 2016/10/04 15:13 (external edit)