User Tools

Site Tools


oly_bx41_zdrive_installation

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
oly_bx41_zdrive_installation [2016/09/07 15:26]
asiadmin ↷ Page moved from documentation:oly_bx41_zdrive_installation to oly_bx41_zdrive_installation
oly_bx41_zdrive_installation [2016/10/03 06:44] (current)
Line 20: Line 20:
 ===== Part 1 - Removing the Left Fine Focus Knob& installing the clutch plate ===== ===== Part 1 - Removing the Left Fine Focus Knob& installing the clutch plate =====
  
-{{ :​documentation:​bx41_2_.jpg?​direct&​300 |}}+{{ bx41_2_.jpg?​direct&​300 |}}
  
-{{ :​documentation:​bx41_3_.jpg?​direct&​300 |}}+{{ bx41_3_.jpg?​direct&​300 |}}
  
 Remove the left fine focus knob from the microscope as follows:  ​ Remove the left fine focus knob from the microscope as follows:  ​
Line 28: Line 28:
 Firmly hold the right fine focus knob with your right hand and turn the left fine focus knob counter clockwise to unscrew it from the fine focus shaft. ​ Firmly hold the right fine focus knob with your right hand and turn the left fine focus knob counter clockwise to unscrew it from the fine focus shaft. ​
  
-{{ :​documentation:​bx41_1_.png?​direct&​300 |}}+{{ bx41_1_.png?​direct&​300 |}}
  
-{{ :​documentation:​bx41_1_.gif?​direct&​300 |}}+{{ bx41_1_.gif?​direct&​300 |}}
  
-{{ :​documentation:​bx41_10_.jpg?​direct&​300 |}}+{{ bx41_10_.jpg?​direct&​300 |}}
  
 Install the clutch plate as follows: Install the clutch plate as follows:
Line 38: Line 38:
 Locate the small brass clutch plate and screw it onto the fine focus shaft in place of the fine focus knob that was just removed. ​ After the clutch plate has been completely screwed onto the fine focus shaft locate the ASI drive and use the 7/64” Allen wrench to loosen the two shaft clamps located near the black encoder case.  Remove the outer shaft from the inner shaft; the outer shaft is threaded. ​ Screw the outer shaft onto the fine focus shaft so that it presses against the brass clutch plate. ​ Slide the clamp assembly against the brass clutch plate and tighten it with the 7/64” Allen wrench. Locate the small brass clutch plate and screw it onto the fine focus shaft in place of the fine focus knob that was just removed. ​ After the clutch plate has been completely screwed onto the fine focus shaft locate the ASI drive and use the 7/64” Allen wrench to loosen the two shaft clamps located near the black encoder case.  Remove the outer shaft from the inner shaft; the outer shaft is threaded. ​ Screw the outer shaft onto the fine focus shaft so that it presses against the brass clutch plate. ​ Slide the clamp assembly against the brass clutch plate and tighten it with the 7/64” Allen wrench.
  
-{{ :​documentation:​bx41_4_.jpg?​direct&​300 |}}+{{ bx41_4_.jpg?​direct&​300 |}}
  
-{{ :​documentation:​bx41_5_.jpg?​direct&​300 |}}+{{ bx41_5_.jpg?​direct&​300 |}}
  
 ===== Part 2 - Installing the Baseplate ===== ===== Part 2 - Installing the Baseplate =====
Line 49: Line 49:
 ===== Part-3 Installing & Aligning the Motor Drive ===== ===== Part-3 Installing & Aligning the Motor Drive =====
  
-{{ :​documentation:​bx41_6_.jpg?​direct&​300 |}}+{{ bx41_6_.jpg?​direct&​300 |}}
                        
-{{ :​documentation:​bx41_7_.jpg?​direct&​300 |}}+{{ bx41_7_.jpg?​direct&​300 |}}
                    
-{{ :​documentation:​bx41_8_.jpg?​direct&​300 |}}+{{ bx41_8_.jpg?​direct&​300 |}}
  
-{{ :​documentation:​bx41_9_.jpg?​direct&​300 |}}+{{ bx41_9_.jpg?​direct&​300 |}}
  
-{{ :​documentation:​bx41_10_.jpg?​direct&​300 |}}+{{ bx41_10_.jpg?​direct&​300 |}}
  
-{{ :​documentation:​bx41_11_.jpg?​direct&​300 |}}+{{ bx41_11_.jpg?​direct&​300 |}}
  
 Locate the ASI fine focus motor drive, vertical adjustment bar, and vertical adjustment screw (M4 x 12 hex screw). ​ Use the 7/64” Allen wrench to loosen the two vertical adjustment screws located on the vertical adjustment bar that is attached to the rear of the drive. Align the drive shaft on the ASI drive with the microscope fine focus shaft / outer shaft that was installed in part #1 and slide the motor drive over the fine focus shaft. ​ Locate the ASI fine focus motor drive, vertical adjustment bar, and vertical adjustment screw (M4 x 12 hex screw). ​ Use the 7/64” Allen wrench to loosen the two vertical adjustment screws located on the vertical adjustment bar that is attached to the rear of the drive. Align the drive shaft on the ASI drive with the microscope fine focus shaft / outer shaft that was installed in part #1 and slide the motor drive over the fine focus shaft. ​
Line 76: Line 76:
 ===== Part 4-Installing the motor drive cover plate & fine focus knob ===== ===== Part 4-Installing the motor drive cover plate & fine focus knob =====
  
-{{ :​documentation:​bx41_1_.jpg?​direct&​300 |}}+{{ bx41_1_.jpg?​direct&​300 |}}
  
-{{ :​documentation:​bx41_12_.jpg?​direct&​300 |}}+{{ bx41_12_.jpg?​direct&​300 |}}
  
 a) Locate the motor drive cover. Remove the 4/40 button head screws from the drive with the 1/16 “ Allen wrench. Position the motor drive covert over the motor drive assembly and secure in place using the 4/40 button head screws.  ​ a) Locate the motor drive cover. Remove the 4/40 button head screws from the drive with the 1/16 “ Allen wrench. Position the motor drive covert over the motor drive assembly and secure in place using the 4/40 button head screws.  ​
oly_bx41_zdrive_installation.txt · Last modified: 2016/10/03 06:44 (external edit)