User Tools

Site Tools


oly_bx51wi_zdrive_installation

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
oly_bx51wi_zdrive_installation [2016/03/30 21:43]
vik created
oly_bx51wi_zdrive_installation [2016/10/04 22:13] (current)
Line 21: Line 21:
 Remove the drive belt cover & left fine focus knob from the microscope as follows: Remove the drive belt cover & left fine focus knob from the microscope as follows:
  
-[{{ :​documentation:​bx51_wi_2_.jpg?​direct&​300 |Figure 1. Pull rubber knob off of front focus knob}}] ​               ​+[{{ bx51_wi_2_.jpg?​direct&​300 |Figure 1. Pull rubber knob off of front focus knob}}] ​               ​
  
-[{{ :​documentation:​bx51_wi_3_.jpg?​direct&​300 |Figure 2.  Use cross blade screw diver to remove belt drive cover}}]+[{{ bx51_wi_3_.jpg?​direct&​300 |Figure 2.  Use cross blade screw diver to remove belt drive cover}}]
  
-[{{ :​documentation:​bx51_wi_4_.jpg?​direct&​300 |Figure 3. Remove outer drive belt}}]+[{{ bx51_wi_4_.jpg?​direct&​300 |Figure 3. Remove outer drive belt}}]
  
-[{{ :​documentation:​bx51_wi_5_.jpg?​direct&​300 |Figure 4. Hold on to right fine focus knob and unscrew the left fine focus knob}}]  +[{{ bx51_wi_5_.jpg?​direct&​300 |Figure 4. Hold on to right fine focus knob and unscrew the left fine focus knob}}]  
  
-[{{ :​documentation:​bx51_wi_6_.jpg?​direct&​300 |Figure 5.  Locate the brass clutch plate}}]+[{{ bx51_wi_6_.jpg?​direct&​300 |Figure 5.  Locate the brass clutch plate}}]
  
-[{{ :​documentation:​bx51_wi_7_.jpg?​direct&​300 |Figure 6.  Install the brass clutch plate by screwing in on in place of the knob removed in figure # 4.   Hold on to right fine focus knob and securely tighten unit}}]+[{{ bx51_wi_7_.jpg?​direct&​300 |Figure 6.  Install the brass clutch plate by screwing in on in place of the knob removed in figure # 4.   Hold on to right fine focus knob and securely tighten unit}}]
  
 As outlined in figures 1 through 6 on the proceeding page remove the original focus drive knobs, belt drive cover & belt drive. ​ Install the brass ASI clutch assembly in place of the knob removed in figure 4. After installing the brass ASI clutch assembly, as shown in figure 6, replace the drive belt that was removed in figure 3.  After the belt has been installed the belt cover that was removed in figure 2 can be reinstalled. As outlined in figures 1 through 6 on the proceeding page remove the original focus drive knobs, belt drive cover & belt drive. ​ Install the brass ASI clutch assembly in place of the knob removed in figure 4. After installing the brass ASI clutch assembly, as shown in figure 6, replace the drive belt that was removed in figure 3.  After the belt has been installed the belt cover that was removed in figure 2 can be reinstalled.
Line 37: Line 37:
 ===== Part 2 - Installing the Baseplate&​ diffuser switch extender ===== ===== Part 2 - Installing the Baseplate&​ diffuser switch extender =====
  
-[{{ :​documentation:​bx51_wi_8_.jpg?​direct&​300 |Figure 7. Baseplate slides under microscope as shown}}]+[{{ bx51_wi_8_.jpg?​direct&​300 |Figure 7. Baseplate slides under microscope as shown}}]
  
-[{{ :​documentation:​bx51_wi_9_.jpg?​direct&​300 |Figure 8. Baseplate needs to be mounted flush with the bottom of the microscope as shown. ​ There should be a small gap between the bottom of the baseplate and tabletop.}}] ​         ​+[{{ bx51_wi_9_.jpg?​direct&​300 |Figure 8. Baseplate needs to be mounted flush with the bottom of the microscope as shown. ​ There should be a small gap between the bottom of the baseplate and tabletop.}}] ​         ​
  
-[{{ :​documentation:​bx51_wi_10_.jpg?​direct&​300 |Figure 9.  While holding baseplate in place against the bottom and the side of the microscope use the 5/64” Allen wrench to tighten the clamp on the right side of the baseplate.}}]+[{{ bx51_wi_10_.jpg?​direct&​300 |Figure 9.  While holding baseplate in place against the bottom and the side of the microscope use the 5/64” Allen wrench to tighten the clamp on the right side of the baseplate.}}]
  
 Locate the baseplate and remove the ASI drive from it (if it is attached) by using the 7/64” Allen wrench to remove the horizontal adjustment screw. ​ Position the base plate assembly it so that the baseplate on the left side of the microscope. ​ Lift the front of the microscope up and slide the base plate under the microscope so that angled portion of the base plate is aligned with the contour of the microscope as shown in figure 7.  Hold the baseplate against the bottom of the microscope as shown in figure 8, and secure the baseplate in place by tightening the setcrew clamp shown in figure 9. Locate the baseplate and remove the ASI drive from it (if it is attached) by using the 7/64” Allen wrench to remove the horizontal adjustment screw. ​ Position the base plate assembly it so that the baseplate on the left side of the microscope. ​ Lift the front of the microscope up and slide the base plate under the microscope so that angled portion of the base plate is aligned with the contour of the microscope as shown in figure 7.  Hold the baseplate against the bottom of the microscope as shown in figure 8, and secure the baseplate in place by tightening the setcrew clamp shown in figure 9.
Line 48: Line 48:
 ===== Installing the diffuser switch extender ===== ===== Installing the diffuser switch extender =====
  
-[{{ :​documentation:​bx51_wi_11_.jpg?​direct&​300 |Figure 10.  Diffuser switch extender.}}]+[{{ bx51_wi_11_.jpg?​direct&​300 |Figure 10.  Diffuser switch extender.}}]
  
-[{{ :​documentation:​bx51_wi_12_.jpg?​direct&​300 |Figure 11.  Installing diffuser switch extender. Use the 0.05 inch Allen wrench to tighten the set screw to hold the unit in place.}}] ​                +[{{ bx51_wi_12_.jpg?​direct&​300 |Figure 11.  Installing diffuser switch extender. Use the 0.05 inch Allen wrench to tighten the set screw to hold the unit in place.}}] ​                
  
-[{{ :​documentation:​bx51_wi_13_.jpg?​direct&​300 |Figure 12.  Diffuser switch extender installed.}}]+[{{ bx51_wi_13_.jpg?​direct&​300 |Figure 12.  Diffuser switch extender installed.}}]
  
-[{{ :​documentation:​bx51_wi_14_.jpg?​direct&​300 |Figure 12.  Diffuser switch extender with switch in second position.}}]+[{{ bx51_wi_14_.jpg?​direct&​300 |Figure 12.  Diffuser switch extender with switch in second position.}}]
  
-[{{ :​documentation:​bx51_wi_15_.jpg?​direct&​300 |Figure 13.  Diffuser switch extender front view of rod extending out.}}] ​                      +[{{ bx51_wi_15_.jpg?​direct&​300 |Figure 13.  Diffuser switch extender front view of rod extending out.}}] ​                      
  
  
Line 63: Line 63:
 ===== Part 3 - Installing and Aligning the Motor Drive ===== ===== Part 3 - Installing and Aligning the Motor Drive =====
  
-[{{ :​documentation:​bx51_wi_16_.jpg?​direct&​300 |Figure 14.  Use the 7/64” Allen wrench to loosen, but do not remove, the two vertical adjustment screws}}]+[{{ bx51_wi_16_.jpg?​direct&​300 |Figure 14.  Use the 7/64” Allen wrench to loosen, but do not remove, the two vertical adjustment screws}}]
  
-[{{ :​documentation:​bx51_wi_17_.jpg?​direct&​300 |Figure 15.  Use the 7/64” Allen wrench to loosen the clamp that is on the drive shaft, then install the drive over the brass shaft as shown.}}]+[{{ bx51_wi_17_.jpg?​direct&​300 |Figure 15.  Use the 7/64” Allen wrench to loosen the clamp that is on the drive shaft, then install the drive over the brass shaft as shown.}}]
           ​           ​
-[{{ :​documentation:​bx51_wi_18_.jpg?​direct&​300 |Figure 16.  The tab on the adjustment bar fits into the grove on the base plate.}}]+[{{ bx51_wi_18_.jpg?​direct&​300 |Figure 16.  The tab on the adjustment bar fits into the grove on the base plate.}}]
        
-[{{ :​documentation:​bx51_wi_19_.jpg?​direct&​300 |Figure 17.   Press the clamp against the brass plate as shown.}}]+[{{ bx51_wi_19_.jpg?​direct&​300 |Figure 17.   Press the clamp against the brass plate as shown.}}]
  
-[{{ :​documentation:​bx51_wi_20_.jpg?​direct&​300 |Figure 18.   Use the 7/64” Allen wrench to tighten the clamp that is on the drive shaft. ​ Insure that this screw is securely tightened to prevent slippage.}}]+[{{ bx51_wi_20_.jpg?​direct&​300 |Figure 18.   Use the 7/64” Allen wrench to tighten the clamp that is on the drive shaft. ​ Insure that this screw is securely tightened to prevent slippage.}}]
  
-[{{ :​documentation:​bx51_wi_21_.jpg?​direct&​300 |Figure 19.  Check for alignment as outlined in the paragraph below, and then secure the horizontal ( as shown here), and the vertical adjustment screws as shown in figure 20.}}] ​        +[{{ bx51_wi_21_.jpg?​direct&​300 |Figure 19.  Check for alignment as outlined in the paragraph below, and then secure the horizontal ( as shown here), and the vertical adjustment screws as shown in figure 20.}}] ​        
  
 Locate the ASI fine focus motor drive, vertical adjustment bar, and vertical adjustment screw (M4 x 12 hex screw). ​ Use the 7/64” Allen wrench to loosen the two vertical adjustment screws located on the vertical adjustment bar as shown in figure14. ​ Align the drive shaft on the ASI drive with the microscope fine focus shaft, as shown in figure 15, and slide the motor drive over the fine focus shaft. ​ Locate the ASI fine focus motor drive, vertical adjustment bar, and vertical adjustment screw (M4 x 12 hex screw). ​ Use the 7/64” Allen wrench to loosen the two vertical adjustment screws located on the vertical adjustment bar as shown in figure14. ​ Align the drive shaft on the ASI drive with the microscope fine focus shaft, as shown in figure 15, and slide the motor drive over the fine focus shaft. ​
Line 83: Line 83:
 Use the 7/64” Allen wrench to screw in the horizontal adjustment screw but leave it loose enough so that the vertical adjustment bar assembly can slide within the groove.  ​ Use the 7/64” Allen wrench to screw in the horizontal adjustment screw but leave it loose enough so that the vertical adjustment bar assembly can slide within the groove.  ​
  
-[{{ :​documentation:​bx51_wi_22_.jpg?​direct&​300 |Figure 20.  .  Check for alignment as outlined in the paragraph below, and then secure the vertical adjustment screws as shown.}}]+[{{ bx51_wi_22_.jpg?​direct&​300 |Figure 20.  .  Check for alignment as outlined in the paragraph below, and then secure the vertical adjustment screws as shown.}}]
  
 Slide the motor drive up and down, forward and backward slightly while turning the right fine focus knob until it is in the position where minimum drag is felt on the right focus knob.  Secure the motor drive into position by tightening the horizontal and vertical adjustment screws. Slide the motor drive up and down, forward and backward slightly while turning the right fine focus knob until it is in the position where minimum drag is felt on the right focus knob.  Secure the motor drive into position by tightening the horizontal and vertical adjustment screws.
Line 93: Line 93:
 ===== Part 4 - Installing the Motor Drive Cover Plate and Fine Focus Knob ===== ===== Part 4 - Installing the Motor Drive Cover Plate and Fine Focus Knob =====
  
-[{{ :​documentation:​bx51_wi_23_.jpg?​direct&​300 |Figure 21.  Installing cover.}}]+[{{ bx51_wi_23_.jpg?​direct&​300 |Figure 21.  Installing cover.}}]
  
-[{{ :​documentation:​bx51_wi_1_.jpg?​direct&​300 |Figure 22.  Installing outer  focus knob}}]  +[{{ bx51_wi_1_.jpg?​direct&​300 |Figure 22.  Installing outer  focus knob}}]  
  
 Locate the motor drive cover. ​ Remove the 4/40 button head screws from the drive with the 1/16” Allen wrench. ​ Position the motor drive cover over the motor drive assembly and secure in place using the 4/40 button head screws. Locate the motor drive cover. ​ Remove the 4/40 button head screws from the drive with the 1/16” Allen wrench. ​ Position the motor drive cover over the motor drive assembly and secure in place using the 4/40 button head screws.
oly_bx51wi_zdrive_installation.txt · Last modified: 2016/10/04 22:13 (external edit)