zeiss_axioplan_axioskop_zdrive
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
zeiss_axioplan_axioskop_zdrive [2016/10/04 18:13] – external edit 127.0.0.1 | zeiss_axioplan_axioskop_zdrive [2021/09/23 17:15] (current) – external edit 127.0.0.1 | ||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ====== Zeiss Axioplan I, Axioskop I, Axioskop FS Installation Procedure ====== | ||
+ | The procedure below outlines the steps necessary to install the ASI Microscope Focus Controller Drive onto the Zeiss Axioplan I/ | ||
+ | |||
+ | To perform these steps you will need the following tools: ASI provides the wrench and hex wrenches. | ||
+ | |||
+ | medium Phillips screwdriver | ||
+ | 14mm wrench | ||
+ | 3mm, 5/ | ||
+ | |||
+ | |||
+ | |||
+ | The procedure has four parts: | ||
+ | |||
+ | - Installing the baseplate. | ||
+ | - Installing the anti-backlash gear. | ||
+ | - Installing and aligning the motor drive assembly. | ||
+ | - Installing the motor drive cover plate & fine focus knob. | ||
+ | |||
+ | ===== Part 1 - Installing the baseplate ===== | ||
+ | |||
+ | [{{ axioplan_1.png? | ||
+ | |||
+ | [{{ axioplan_2.png? | ||
+ | |||
+ | [{{ axioplan_3.png? | ||
+ | | ||
+ | Locate the baseplate/ | ||
+ | |||
+ | ===== Part 2 - Installing the anti-backlash gear ===== | ||
+ | |||
+ | [{{ axioplan_4.png? | ||
+ | | ||
+ | [{{ axioplan_5.png? | ||
+ | |||
+ | [{{ axioplan_6.png? | ||
+ | |||
+ | |||
+ | Remove the left fine focus knob from the microscope by loosening the setscrew, located in the side of the knob, using the 1.5mm hex wrench and then sliding the knob off the shaft. | ||
+ | |||
+ | Remove the left coarse focus knob by first removing the nut, using the 14mm deep socket provided, and then unscrewing the coarse focus knob. The nut and knob turn counter-clockwise to unscrew. | ||
+ | |||
+ | Locate the anti-backlash gear. Screw it onto the coarse focus threaded bushing. | ||
+ | |||
+ | ===== Part 3 - Installing and aligning the motor drive assembly ===== | ||
+ | |||
+ | [{{ axioplan_7.png? | ||
+ | | ||
+ | [{{ axioplan_8.png? | ||
+ | |||
+ | {{ axioplan_9.png? | ||
+ | |||
+ | |||
+ | Loosen the horizontal adjustment screw just enough so that the adjustment bar can slide in the groove. | ||
+ | |||
+ | |||
+ | Locate the motor drive assembly. | ||
+ | |||
+ | Slide the drive shaft to the outside. The drive shaft is the shaft in the middle that goes through the pair of bearings in the driveplate. | ||
+ | |||
+ | Orient the motor drive assembly with respect to the left side of the microscope so that the curved portion of the driveplate faces forward and up and the cable extends rearward. | ||
+ | |||
+ | Position the motor drive assembly onto the adjustment bar so that the notches in the edges of the driveplate align with the ridges in the edges of the adjustment bar. Thread in, but do not tighten, the vertical adjustment screw that was removed when taking the drive off of the baseplate | ||
+ | |||
+ | [{{ axioplan_10.png? | ||
+ | |||
+ | [{{ axioplan_11.png? | ||
+ | |||
+ | [{{ axioplan_12.png? | ||
+ | |||
+ | [{{ axioplan_13.png? | ||
+ | |||
+ | [{{ axioplan_14.png? | ||
+ | |||
+ | While sliding in the drive shaft, maneuver the motor driveplate forward and backward, up and down, until the drive shaft is axially aligned with the fine focus shaft. | ||
+ | |||
+ | Position the hub clamp midway over the slotted portion of the drive shaft (over the fine focus shaft) and tighten in place using the 7/64” hex wrench. After installing drive, tighten baseplate clamp to secure drive to the microscope. | ||
+ | |||
+ | To insure perfect axial alignment, loosen the horizontal and vertical adjustment screws, then re-tighten while rotating the right fine focus knob. There should be no noticeable increase in friction as the screws are tightened. | ||
+ | |||
+ | Check to make sure that the drive shaft clamp is securely tightened by holding the drive shaft gear, the one that mates with the outer clutch gear, while turning the right fine focus knob. No slippage should occur. | ||
+ | |||
+ | Using the .050” hex wrench, loosen the small setscrew in the small gear below and forward of the anti-backlash gear. Rotate the anti-backlash gear until the black marks in the gearteeth are visible. | ||
+ | |||
+ | ===== Part 4 - Installing the Cover and Fine Focus Knob ===== | ||
+ | |||
+ | {{ axioplan_15.png? | ||
+ | |||
+ | {{ axioplan_16.png? | ||
+ | |||
+ | |||
+ | Remove the three screws from the edge of the baseplate. | ||
+ | |||
+ | Locate the original fine focus knob. Slide it onto the fine focus shaft extension until there is a small gap between it and the cover. | ||
+ | |||
+ | {{tag> |
Address: 29391 W Enid Rd. Eugene, OR 97402, USA | Phone: +1 (541) 461-8181